YOUR PLUMBING CRASH COURSE: A NECESSITY FOR BATHTUB INSTALLATION

Your Plumbing Crash Course: A Necessity for Bathtub Installation

Your Plumbing Crash Course: A Necessity for Bathtub Installation

Blog Article

Call

The author is making a few good pointers about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content below.


How to Install a Bathtub
Mounting a bathtub isn't exactly rocket science, but it does need solid plumbing, woodworking, and also often, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult project. If the old bathtub is conveniently accessible, the task can move speedily; if you need to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the brand-new one. Make certain you have actually qualified on your own for the work and fit trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to take into consideration employing one before you begin. Opportunities are you might require an expert plumber to make tube links.
This short article will certainly assist you install a brand-new bath tub in your washroom if you have currently gotten a new tub and do not require to change the plan of your previous water supply pipelines.
Your tools and also product checklist need to consist of the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the restricted gain access to that is often the situation.
    Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the staying water that will originate from the pipes. Once the supply pipes have been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
    Prior to going on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next, place the tap in the installing hole in the bath/basin ensuring that the washing machines are in place between the tap and the sink. Safeguard the tap in position with the manufacturer supplied backnut. When the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The former type should be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Mounting the Tub


    Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little points.
    The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the tub up until the level reads degree.
    To set up faucets, fit the bottom of the outermost adaptable tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
    Turn on the supply of water as well as inspect all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the tub as well as likewise inspect the overflow electrical outlet and also the typical electrical outlet for leaks.
    Lastly, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub should wait until the tub has actually been used at least once as this will certainly resolve it into its last setting.

    Preparing for the Setup


    To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to avoid pressure on the bath tub.
    Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its last placement.

    Tiling Around the Bath tub


    In the area where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, resulting in problems with dampness as well as feasible leakages to the ceiling below.
    You can select from a variety of coloured sealers to blend in your components and also installations. They are marketed in tubes and also cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can crack relatively very early if you do not consider this activity before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or waterproof adhesive and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    We hope you liked our part on How to Install a Bathtub Yourself. Thanks for taking a few minutes to read our article post. Make sure you take a moment to distribute this write-up if you liked it. Thanks a lot for your time. Visit us again soon.


    Address plumbing needs.

    Report this page